JUST HOW TO INSTALL A BATHTUB YOURSELF

Just How to Install a Bathtub Yourself

Just How to Install a Bathtub Yourself

Blog Article

Get A Free Quote

Right here in the next paragraph you can locate a lot of incredibly good information around A Step-by-Step Guide to Installing a Bathtub.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old tub is easily obtainable, the project can move rapidly; if you have to open up a wall surface to eliminate the old bathtub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to alter the arrangement of your previous supply of water pipes.
Your tools and material list need to consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
    Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washing machines.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted gain access to that is often the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
    The next objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
    To set up faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
    Turn on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
    Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at the very least when as this will certainly settle it into its final position.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipes.
    If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous kind ought to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with wetness and feasible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion before sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Hopefully you enjoyed reading our topic on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to read our article post. Enjoyed our review? Please share it. Help someone else check it out. Thanks a bunch for your time. Visit us again soon.




    Here


    Report this page